USING THE SNOOZE FEATURE
the radio frequency appears.
mode. The time appears if the radio is off. If the radio is on, pressing [MODE], the radio automatically returns to the previousNOTE: If you do not set the alarm time within about 10 seconds afterdisplay. The alarm time appears. To view the alarm time, press [MODE] until ‘ON TIME’ flashes on the[ALARM] until the ‘ALARM’ indicator disappears from the display. To set the alarm so the radio does not play at the set alarm time, pressonce. ‘ALARM’ disappears from the display and the radio turns off. To turn off the alarm before the two hours have passed, press [ALARM]alarm time. the display. The radio automatically turns off two hours after the setThe radio automatically turns on at the alarm time and ‘ALARM’ flashes on and ‘ALARM’ appear on the display. 5. Press [MODE] once to return to the normal time display. Both ‘CLOCK’ the alarm is on. 4. Press [ALARM] once. ‘ALARM’ appears on the display, indicating that Press and hold down [MIN] for rapid setting. 3. While holding down [TIME], press [MIN] to set the alarm minutes. set the alarm hour. Press and hold down HR for rapid setting. 2. Press and hold down [TIME]. While holding down [TIME], press [HR] to1. Press [MODE] until ‘ON TIME’ flashes on the display. Follow these steps to set the alarm time: SETTING THE ALARM are listening to the radio. NOTE: Press [MODE] twice to return to the radio frequency display if you hold down [MIN] for rapid setting. 3. While holding down [TIME], press [MIN] to set the minutes. Press and set the hour. Press and hold down HR for rapid setting. 2. Press and hold down [TIME]. While holding down [TIME], press [HR] to1. Press [MODE] until ‘Clock’ and ‘AM’ or ‘PM’ appear on the display. Follow these steps to set the time: SETTING THE TIME Clock Operation (120-0626) Operation Faxback Doc. # 49089 AM/FM Travel Clock Radio
USING THE SLEEP FEATURE station replaces the previously stored station. To change the stations stored in memory, repeat Steps 1 to 5. The new the station’s frequency appears on the display. to store the station in that memory location. ‘MEMORY’ disappears and5. While ‘MEMORY’ is displayed, press one of the memory buttons (1 to 5)4. Press [MEM]. ‘MEMORY’ appears on the display for about 5 seconds. 3. Press [TUNING < -] or [->] to tune to the station you want to store. 2. Set [FM/AM] to the desired band. 1. To turn on the radio, set [ON/OFF] to ON. button.can instantly tune to the stored station by pressing the designated memoryYou can store up to 10 radio stations (5 AM and 5 FM) in memory. Then youSTORING STATIONS IN MEMORY 5. To turn off the radio, set [ON/OFF] to ‘OFF’. reception, extend the telescoping antenna to its full length. Rotate the radio for the best AM reception. For best FM NOTE: The radio has two antennas. The AM antenna is built-in. that frequency. radio finds the next active station in that direction and locks on To scan, press [TUNING < -] or [->] for more than one second. The station. 4. Press and hold down [TUNING < -] or [->] to tune to the desired 3. Adjust VOLUME to a comfortable listening level. to show which band you have selected. 2. Set [FM/AM] to the desired band. ‘AM’ or ‘FM’ appears on the display1. Set [ON/OFF] to ON to turn on the radio. Follow these steps to operate the radio. PLAYING THE RADIO RADIO OPERATION 24 hours later. 2 hours, the radio will not come on again until the set alarm timeNOTE: You can use the snooze feature repeatedly for up to 2 hours. Afterminutes, press [SNOOZE]. This silences the radio for about 9 minutes. If you wish to silence the alarm, but want it to sound again in a few
(EB – Rev. 3/15/99) (wr 05/09/98) again.To turn off the radio before the set sleep time has passed, press [SLEEP]minimum is 1 minute. in 10 minute increments. The maximum sleep time is 90 minutes and theTo reduce the sleep time, press and hold [SLEEP]. The sleep time reducesoff automatically after 90 minutes. After about 5 seconds, the normal time display appears. The radio turns plays. 2. Press [SLEEP]. ’90’ and ‘SLEEP’ appear on the display and the radio1. Set [ON/OFF] to ‘OFF’. To use the sleep feature, follow these steps: turn off. You can set the radio to play for up to 90 minutes, then automatically
